1
00:00:00,720 --> 00:00:05,240
This is the video for the third exercise we are going to do with the SketchUp.

2
00:00:05,240 --> 00:00:12,240
In this exercise we will have to do this object here, and here you will have the measure.

3
00:00:12,240 --> 00:00:14,919
So let's start with this.

4
00:00:14,919 --> 00:00:25,699
So always remember, when creating a new one, choose the template in millimeters.

5
00:00:25,699 --> 00:00:27,980
So let's start by doing the base.

6
00:00:27,980 --> 00:00:37,759
As you can see here the base is 100mm this side and 360mm this other and then 20mm height.

7
00:00:37,759 --> 00:00:48,359
So let's start with the measure tool to write, remember to write the measures with the keyboard.

8
00:00:48,359 --> 00:00:58,509
Press enter, this is the same 100mm and this other 360mm.

9
00:00:58,509 --> 00:01:09,269
the measures with the keyboard and press enter to pull them, once I have this I can choose

10
00:01:09,269 --> 00:01:20,609
the square tool or rectangle tool and make a rectangle using the points we take as reference

11
00:01:20,609 --> 00:01:28,930
and then again writing the height with the keyboard and this will be the base.

12
00:01:28,930 --> 00:01:35,590
The next part we will have to place these two structures over the base and we can see

13
00:01:35,590 --> 00:01:46,909
that the center of each one is the first one at 120mm from the border and the other at

14
00:01:46,909 --> 00:01:54,409
another 120 millimeters from the first one so let's use again the measure tool

15
00:01:54,409 --> 00:02:09,900
to make those marks so from here we write 120 and since I take from the

16
00:02:09,900 --> 00:02:20,340
middle it just make a line parallel to this other if I take for another from a

17
00:02:20,340 --> 00:02:28,560
corner for example like this I could make the line in the other axis but

18
00:02:28,560 --> 00:02:39,819
right now it is useful to do it this way and now the other will be at 240 from

19
00:02:39,819 --> 00:02:48,039
this point I will make a mark at 50 millimeters to make the middle and

20
00:02:48,039 --> 00:02:55,659
another mark here so this will be the center of this other two structures so

21
00:02:55,659 --> 00:03:01,419
the next part will be first to make the hexagon here and then the circle or I

22
00:03:01,419 --> 00:03:06,819
could make the circle first and after that the hexagon for the circle I see

23
00:03:06,819 --> 00:03:17,030
that it is 40 millimeters diameter so I'm going to to make first the hexagon

24
00:03:17,030 --> 00:03:30,430
the hexagon I see that it is 80 millimeters and also it is in parallel

25
00:03:30,430 --> 00:03:36,949
to this side so from this point I'm taking this line as a reference I will

26
00:03:36,949 --> 00:03:52,699
have to write 30 80 millimeters so it will be 40 millimeters radius like this

27
00:03:52,699 --> 00:04:09,569
and now to push it and see its height is 30 millimeters so I write 30 now I will

28
00:04:09,569 --> 00:04:16,449
have to mark the middle of the hexagon again so I could I can just make this

29
00:04:16,449 --> 00:04:26,810
line and then this other and I will have here the middle and take the the circle

30
00:04:26,810 --> 00:04:49,560
to make a circle of 40 mm diameter. So I am going to write a circle. Remember to write

31
00:04:49,560 --> 00:04:56,519
like this. And I will continue in the next video. Remember the radius is 20 mm.