1
00:00:00,300 --> 00:00:36,799
well by clicking and we have only see it would be very complicated so the more

2
00:00:36,799 --> 00:00:47,119
simple, the simplest to simplify the process, we just only see the basic things. Well, here we are,

3
00:00:47,119 --> 00:00:54,079
this is the Regeter host and as you see, you can see the feature, you can see what you want to

4
00:00:54,079 --> 00:01:02,799
print here in this part of the program. We also have some functions here in the top of the program

5
00:01:03,759 --> 00:01:17,359
and also there are some other important functions there so if you want just only go to

6
00:01:18,560 --> 00:01:28,969
upload to open the stl file for example this one

7
00:01:28,969 --> 00:01:36,969
like this, this adverb object, but it is now in .stl format.

8
00:01:36,969 --> 00:01:43,969
We want to create a file which format should be a gcode.

9
00:01:43,969 --> 00:01:57,890
So, what you have to do is come here

10
00:01:57,890 --> 00:02:02,890
and you can see the configuration of the regular host.

11
00:02:07,230 --> 00:02:12,229
You can change the main parameters of the slicer.

12
00:02:14,050 --> 00:02:19,050
So you usually can have a file with these specific things.

13
00:02:24,729 --> 00:02:28,509
So if you want to create a decode file,

14
00:02:28,509 --> 00:02:43,120
just click in this section and you can get the file.

15
00:02:43,120 --> 00:02:55,120
You need more than 4 hours to print this file with 450 libres and so on.

16
00:02:55,120 --> 00:03:01,120
These are the parameters of the printing process.

17
00:03:01,120 --> 00:03:17,120
You can create your own parameters, for example, you can change the number of layers, you can change, for example, also the temperature for the printer, that usually is about 210.

18
00:03:17,120 --> 00:03:25,120
It depends, obviously, the material in which you are going to print in the object.

19
00:03:25,120 --> 00:03:41,120
For PLA, usually it's enough with 210 degrees, but you can change it if you want.

20
00:03:41,120 --> 00:03:57,680
and now this is the HECO you should you can edit the HECO you should save this file in a SD card

21
00:03:57,680 --> 00:04:25,040
to print this object in the printer so and then this is our file that we can use for the printer

22
00:04:25,040 --> 00:04:39,180
it's not for you you there modifies you see here parameters for the printer parameter for

23
00:04:39,180 --> 00:04:43,180
For the extruder, there is a little bit high,

24
00:04:43,180 --> 00:04:45,879
this temperature, let's start.

25
00:04:45,879 --> 00:04:49,279
No more than 230 degrees,

26
00:04:49,279 --> 00:04:54,279
so about 250 more or less is the dimensions.

27
00:04:55,079 --> 00:05:00,079
So, there are the parameters for our printer.

28
00:05:02,500 --> 00:05:03,500
And you can change,

29
00:05:05,360 --> 00:05:09,100
here you can change the difference parameter,

30
00:05:09,100 --> 00:05:17,370
That is not necessary, right?

31
00:05:17,370 --> 00:05:21,329
That is all about Redditor host.